Jun 12 11:21:30:I:[958] slot 1 XPPSP40G 0 Non mask info: Parity reg: a/v/m: 00000230/00010000/0000f000
Never seen this one before
Jun 12 11:21:30:I:[958] slot 1 XPPSP40G 0 Non mask info: Parity reg: a/v/m: 00000230/00010000/0000f000
Never seen this one before
Brocade
ip access-list extended anti-multicast
deny ip any 224.0.0.0 15.255.255.255 log
deny ip 224.0.0.0 15.255.255.255 any log
permit ip any any
int e 18
ip access-group anti-multicast in
https://supportforums.cisco.com/document/12013356/implementing-anti-spoofing-access-list
Brocade MLX
$ ssh [email protected] Unable to negotiate with 1.2.3.4 port 22: no matching key exchange method found. Their offer: diffie-hellman-group1-sha1
… in the ~/.ssh/config file:
Host br1.wikirouters.com
KexAlgorithms +diffie-hellman-group1-sha1
[email protected](config-lag-Switch)#deploy Telnet Session 3 in secondary port (14/4) of this LAG: Deploy Failed [email protected](config)#sh telnet Console connections: established, monitor enabled, privilege read-only 165 days 41 minutes 57 seconds in idle Telnet server status: Enabled Telnet connections (inbound): 1 established, client ip address 1.2.3.4, user is username, privilege super-user, in config mode using vrf default-vrf. you are connecting to this session 1 seconds in idle 2 closed 3 closed 4 closed 5 closed Telnet connections (outbound): 6 closed 7 closed 8 closed 9 closed 10 closed
crazy a bunch of router cards were crashing
“#show save” shows task: LP-IKE is responsible
BEGIN: show save CONTEXT: MP TIME-STAMP: 2155905152 milli sec since device started ============================================================ Active MP crash dump area clean Standby MP crash dump area clean ======================================================================== NetIron XMR Crash Dump Version 1.1 Retrieved from Line Card on Slot 1 Module Type : LP Boot : 05.09.00T175 xmlprm05900 built on Mar 19 2015 at 03:17:00 Monitor : 06.00.00T175 xmlb06000 built on Jun 7 2016 at 16:09:50 System : 06.00.00aT177 xmlp06000a built on Aug 6 2016 at 00:18:20 Current Task : LP-IKE Created on : 22:41:45 Pacific Sun Sep 18 2016 System had been up for 3 minutes EXCEPTION 1200, Data TLB error Task : LP-IKE GP Registers r0 : 21225980 3d592cd0 2166ccf0 65652035 r4 : 65652035 00000000 00000020 00000000 r8 : 3d592e5c 3d592e5f 04962000 00000000 r12 : 0000009f 21ced470 00000000 00000000 r16 : 00000000 00000000 00000000 00000000 r20 : 00000001 ffffffff 04a25200 00000000 r24 : 21cc49dc 04960000 00000000 00000000 r28 : 65652035 00000000 00000000 00000000
here is a quick fix.
Fixes in image will be released tomorrow 2016-09-20
NOTE: If customer has active IPSec traffic in the network, DO NOT USE this ACL. We don’t have 100% proof but they may not be hitting this defect.
ip access-list extended BLOCK_IKE
deny udp any any eq isakmp
deny udp any any eq 4500
permit ip any any
!
ip access-list extended PERMIT_ANY
permit ip any any
ip receive access-list BLOCK_IKE sequence 5
ip receive access-list PERMIT_ANY sequence 99
ip receive access-list enable-deny-logging
sh access-list receive accounting name BLOCK_IKE
bit_err_bitmap: 0
is_clocking_err: 0
is_dqs_con_err[0]: 0
is_dqs_con_err[1]: 0
is_dqs_con_err[2]: 0
is_dqs_con_err[3]: 0
is_phy_ready_err: 0
is_rtt_avg_min_err: 1
is_rtt_avg_max_err: 0
**>’error in petra_mgmt_hw_adjust_ddr()’ –
Err code: 0x14C5E59E (fail):
Name: PETRA_MGMT_DRAM_INIT_FAILS_ERR
Desc: The DPI-ready indication did not rise upon DRAM initialization
For a detailed diagnostics to be printed, if printing is allowed,
SAND_DEBUG must be set to SAND_DBG_LVL2
Note: verify that TRST signal is low (possible error cause)
Procedure id: 0x005E (Mod: PETRA module, Proc: PETRA_MGMT_HW_ADJUST_DDR)
exit place: 182, params: 0 0 0
**>’error in petra_mgmt_hw_interfaces_set_unsafe()’ –
Err code: 0x1402A59E (fail):
Name: PETRA_MGMT_DRAM_INIT_FAILS_ERR
Desc: The DPI-ready indication did not rise upon DRAM initialization
For a detailed diagnostics to be printed, if printing is allowed,
SAND_DEBUG must be set to SAND_DBG_LVL2
Note: verify that TRST signal is low (possible error cause)
Procedure id: 0x002A (Mod: PETRA module, Proc: PETRA_MGMT_HW_INTERFACES_SET_UNSAFE)
exit place: 10, params: 0 0 0
**>’error in petra_mgmt_init_sequence_phase1_unsafe()’ –
Err code: 0x14AC059E (fail):
Name: PETRA_MGMT_DRAM_INIT_FAILS_ERR
Desc: The DPI-ready indication did not rise upon DRAM initialization
For a detailed diagnostics to be printed, if printing is allowed,
SAND_DEBUG must be set to SAND_DBG_LVL2
Note: verify that TRST signal is low (possible error cause)
Procedure id: 0x00C0 (Mod: PETRA module, Proc: PETRA_MGMT_INIT_SEQUENCE_PHASE1_UNSAFE)
exit place: 60, params: 0 0 0
**>’error in petra_mgmt_init_sequence_phase1()’ –
Err code: 0x1401659E (fail):
Name: PETRA_MGMT_DRAM_INIT_FAILS_ERR
Desc: The DPI-ready indication did not rise upon DRAM initialization
For a detailed diagnostics to be printed, if printing is allowed,
SAND_DEBUG must be set to SAND_DBG_LVL2
Note: verify that TRST signal is low (possible error cause)
Procedure id: 0x0016 (Mod: PETRA module, Proc: PETRA_MGMT_INIT_SEQUENCE_PHASE1)
exit place: 110, params: 0 0 0
Init Petra dev = 0 – ERROR = 1.
++++++++++ The mesh topology retry history dev: 0 count 0:
++++++++++ Mesh 0x3445:[000, 000, 000, 000, 000, 000, 000, 000, 000, 000, ]
++++++++++ Mesh 0x3445:[000, 000, 000, 000, 000, 000, 000, 000, 000, 000, 000, ]
+ fdry_tm_init: ERROR 7.
Module is down. reason CARD_DOWN_REASON_TM_INIT_FAIL, Err Code = 5.
Setting hitless base 18a00140 size 3dffec0
CPU Protection Initialization failed due LP init failure
May 19 00:31:37:N:System: Module 1 powered off
May 19 00:31:37:I:System: Interface L2-SW04-e2/3/1 1/8, state down – card down
May 19 00:31:37:I:System: Interface L2-TSW-E24 1/7, state down – card down
May 19 00:31:37:I:System: Interface L2-VDX-TE1/0/54 1/6, state down – card down
May 19 00:31:37:N:System: Module down in slot 1, reason CARD_DOWN_REASON_POWERED_OFF_SYS_MONITOR. Error Code 0
May 19 00:31:37:D:System: TM Health Monitoring detects an issue in slot 1 ppcr 0 Reg Offset 00000800 Value 00000005
May 19 00:31:37:D:System: Module reset in slot 1, triggered by TM Health Monitoring
May 19 00:31:36:A:System: LP1/TM0: All ports down due to dram crc
May 19 00:31:36:I:System: Interface L2-SW03-e1/3/1 1/3, state down – ingress dram crc
May 19 00:31:36:I:System: Interface L2-TSW-E24 1/2, state down – ingress dram crc
May 19 00:31:36:I:System: Interface L2-VDX-TE1/0/54 1/1, state down – ingress dram crc
Brocade NetIron MLX
Apr 19 04:19:05:N:System: Module down in slot 1, reason CARD_DOWN_REASON_LOSS_HEARTBEAT. Error Code 0