bit_err_bitmap: 0
is_clocking_err: 0
is_dqs_con_err[0]: 0
is_dqs_con_err[1]: 0
is_dqs_con_err[2]: 0
is_dqs_con_err[3]: 0
is_phy_ready_err: 0
is_rtt_avg_min_err: 1
is_rtt_avg_max_err: 0

**>’error in petra_mgmt_hw_adjust_ddr()’ –
Err code: 0x14C5E59E (fail):
Name: PETRA_MGMT_DRAM_INIT_FAILS_ERR
Desc: The DPI-ready indication did not rise upon DRAM initialization
For a detailed diagnostics to be printed, if printing is allowed,
SAND_DEBUG must be set to SAND_DBG_LVL2
Note: verify that TRST signal is low (possible error cause)
Procedure id: 0x005E (Mod: PETRA module, Proc: PETRA_MGMT_HW_ADJUST_DDR)
exit place: 182, params: 0 0 0

**>’error in petra_mgmt_hw_interfaces_set_unsafe()’ –
Err code: 0x1402A59E (fail):
Name: PETRA_MGMT_DRAM_INIT_FAILS_ERR
Desc: The DPI-ready indication did not rise upon DRAM initialization
For a detailed diagnostics to be printed, if printing is allowed,
SAND_DEBUG must be set to SAND_DBG_LVL2
Note: verify that TRST signal is low (possible error cause)
Procedure id: 0x002A (Mod: PETRA module, Proc: PETRA_MGMT_HW_INTERFACES_SET_UNSAFE)
exit place: 10, params: 0 0 0

**>’error in petra_mgmt_init_sequence_phase1_unsafe()’ –
Err code: 0x14AC059E (fail):
Name: PETRA_MGMT_DRAM_INIT_FAILS_ERR
Desc: The DPI-ready indication did not rise upon DRAM initialization
For a detailed diagnostics to be printed, if printing is allowed,
SAND_DEBUG must be set to SAND_DBG_LVL2
Note: verify that TRST signal is low (possible error cause)
Procedure id: 0x00C0 (Mod: PETRA module, Proc: PETRA_MGMT_INIT_SEQUENCE_PHASE1_UNSAFE)
exit place: 60, params: 0 0 0

**>’error in petra_mgmt_init_sequence_phase1()’ –
Err code: 0x1401659E (fail):
Name: PETRA_MGMT_DRAM_INIT_FAILS_ERR
Desc: The DPI-ready indication did not rise upon DRAM initialization
For a detailed diagnostics to be printed, if printing is allowed,
SAND_DEBUG must be set to SAND_DBG_LVL2
Note: verify that TRST signal is low (possible error cause)
Procedure id: 0x0016 (Mod: PETRA module, Proc: PETRA_MGMT_INIT_SEQUENCE_PHASE1)
exit place: 110, params: 0 0 0

Init Petra dev = 0 – ERROR = 1.

++++++++++ The mesh topology retry history dev: 0 count 0:
++++++++++ Mesh 0x3445:[000, 000, 000, 000, 000, 000, 000, 000, 000, 000, ]
++++++++++ Mesh 0x3445:[000, 000, 000, 000, 000, 000, 000, 000, 000, 000, 000, ]
+ fdry_tm_init: ERROR 7.
Module is down. reason CARD_DOWN_REASON_TM_INIT_FAIL, Err Code = 5.
Setting hitless base 18a00140 size 3dffec0
CPU Protection Initialization failed due LP init failure

Leave a Reply

Your email address will not be published. Required fields are marked *

Post Navigation